PC924X opic photocoupler (1) igbt drive for inverter control internal connection input forward current i f 25 ma v r 6v output supply voltage v cc 35 v i o1 0.1 a i o1p 0.4 a i o2 0.1 a i o2p 0.4 a v o1 35 v power dissipation p o 500 mw total power dissipation p tot 550 mw isolation voltage v iso(rms) 5.0 kv operating temperature t opr -20 to +80 storage temperature t stg -55 to +125 ?c soldering temperature t sol 260 *3 40 to 60%rh, ac for 1 minute, ta=25?c *2 pulse width 0.15 s, duty ratio= 0.01 *2 *2 o 1 o 1 o 2 o 2 o 1 output current peak output current output current peak output current output voltage 6.5 7 5 6 8 1 2 3 4 9.66 1.2 0.85 7.62 0.26 2.54 0.5 3.4 3.05 0.5 3.5 interface 87 6 1 23 4 5 3 nc 4 nc 7 gnd 5 o 1 6 o 2 8 vcc 1 anode 2 cathode (unit : mm) outline dimensions features applications absolute maximum ratings (notice) ? in the absence of device specification sheets, sharp takes no responsibility for any defects that may occur in e quipment using any sharp device shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification shee ts before using any sharp device. ? specifications are subject to change without notice for improvement. (internet) ? data for sharp's optoelectronic/power device is provided for internet. (address http://www.sharp.co.jp/ecg/) parameter symbol ratings unit reverse voltage *1 *3 *4 (unless specified, ta=t opr ) ?c ?c *1 ta=25?c *4 for 10s pc924 * "opic" (optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and signal- processing circuit integrated onto a single chip. built-in direct drive circuit for igbt drive (i o1p , i o2p : 0.4 a) high speed response (t phl ,t plh : max. 2.0 s) wide operating supply voltage range (v cc : 15 to 30 v, ta= -10 to 60 ?c ) high noise reduction type (cm h =min. -1 500 v/ s) (cm l =min. 1 500 v/ s) high isolation voltage (viso ( rms ) : 5 kv) opic photocoupler for igbt drive of inverter (1) (2) (3) (4) (5)
PC924X o 2 output tr. 1 tr. 2 on high level on off off low level off on (unless specified, ta=t opr ) min. typ. max. v f1 1.2 1.4 v v f2 0.6 0.9 v i r 10 c t 30 250 pf v cc 15 30 v v o1l 0.2 0.4 v v o2h 18 21 v v o2l 1.2 2.0 v i o1l 500 i o2l 500 a i cch 610ma 14 ma i ccl 813ma 17 ma i flh 1.0 4.0 7.0 ma v cc = 24 v 0.6 10.0 ma r iso 40 to 60 %rh 5 x 10 10 1 x 10 11 ? t plh t a = 25 ? c, v cc = 24 v, i f = 10 ma, r g = 47 ?, c g = 3000 pf 1.0 2.0 t phl 1.0 2.0 rise time t r 0.2 0.5 t r 0.2 0.5 cm h -1 500 cm l v cc = 24 v, ? v o2l = 2.0 v 1 500 v/ s parameter symbol conditions unit input "low high"transfer time "high low"transfer time t a =25 ? c, v cm =600 v ( peak) , i f = 0 ma electro-optical characteristics v cc = 24 v, ? v o2h = 2.0 v t a =25 ? c, v cm =600 v ( peak) , i f =10 ma t a = 25 ? c, dc= 500 v t a =25 ? c, v cc = 24 v t a = -10 to 60 ? c v cc = 24 v , i f = 0 ma t a =25 ? c, v cc = 24 v , i f = 0 ma v cc = 24 v , i f = 10 ma t a =25 ? c, v cc = 24 v , i f = 10 ma t a = 25 ? c, v cc = v o2 = 35 v , i f =10 ma t a = 25 ? c, v cc = v o1 = 35 v , i f =0 ma v cc = 24 v , i o2 = 0.1 a, i f = 0 i f = 10 ma v cc = v o1 = 24 v , i o2 = -0.1 a, v cc1 =12 v , v cc2 = -12 v , i o1 = 0.1 a, i f = 10 ma t a =25 ? c, v= 0, f= 1 khz t a = 25 ? c, v r = 4 v t a = 25 ? c, i f = 0.2 ma t a = 25 ? c, i f =20 ma ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 15 24 v ? ? ? ? ? ? ? ? v/ s s a a forward voltage reverse current operation temperature supply voltage o 1 low level output voltage o 2 high level output voltage o 2 low level output voltage o 1 leak current o 2 leak current high level supply current low level supply current fall time opic photocoupler terminal capacitance "low high" thresh hold input current *5 isolation resistance *5 i flh is forward current when output become "low" to "high" *6 when measuring output and transfer characteristics, connect a by-pass capacitor(0.01 f or more) between v cc and gnd near the device. transfer characteristics input output response time instantaneous common mode rejection voltage "output:high level" instantaneous common mode rejection voltage "output: low level" truth table
115 application circuits notice l the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. l contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. l observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- office automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii)measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: --- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traffic signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii)sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment --- medical and other life support equipment (e.g., scuba). l contact a sharp representative in advance when intending to use sharp devices for any "specific" applications other than those recommended by sharp or when it is unclear which category mentioned above controls the intended use. l if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade control law of japan, it is necessary to obtain approval to export such sharp devices. l this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. l contact and consult with a sharp representative if there are any questions about the contents of this publication.
|
